Payment & Shipping Terms:
|Material:||Inner Material SUS 304 Stainless Steel||Size:||Standard Or Customized|
|Color:||White||Voltage:||AC220V 50HZ / AC380V 50HZ|
|Advantage:||Laboratory Or Industrial Drying Oven||Export Material:||1.2 Mm Thickness Cold Rolled Steel Coating|
Customized LCD Precision Large Laboratory Oven For Sale LabTesting Equipment
1. The material room
The material is put in the form of pallet structure, and the material room and the heating room are separated by iron plate.
2. The heating chamber
Install the electric heating equipment, generate the space of hot air, install the blower in the proper place, and send the hot air into the material room when the blower runs.
3. Hot air transport mode.
The circulating fan sends the hot air into the hot air passage, then enters the material chamber through the small holes in the pallet rack, and adopts the left and right air supply mode to make the drying more uniform.
4. Heating equipment
Hot air generator, electric heating, finned tube form.
5. Ventilation and dehumidification equipment.
Keep the air in the heating room and the material room circulation and realize the air exchange in the dryer, and maintain the equipment for the indoor baking process.Including the cold wind inlet door, the dehumidifier, and other equipment models different ventilation and dehumidification equipment.
6. Temperature and humidity control equipment.
Equipment used to detect, display and control the process conditions of the material baking process, including temperature sensor, control host and actuator.Through the regulation of heating equipment, the automatic control of baking is realized.
1. Size and internal dimensions of the box:
1 internal dimension: 420L inner width 700 x 600 x height 1000mm.
2. Power supply voltage: 380V 50/60hz;
3 heating power: about 5KW.
The controller is located above the stand.
5 inner material 304 stainless steel plate, plate thickness of 1.0mm high quality steel plate spray treatment.
6. Thermal insulation material is imported glass rock wool, with good heat insulation and maximum temperature insulation. It is made of high temperature resistant silica gel, which can withstand high temperature of 200 degrees for a long time.
Ii. Temperature control system:
1. Adjustable control within the temperature range of room temperature ~ 200.
2 precision: control precision
3 plus or minus 2.0 ℃ temperature distribution (light)
4 heating rate: RT ~ 100 (about 10 minutes)
5 for PID temperature control microcomputer automatic calculus of PV/SV display at the same time, can be in the range of allowable temperature of the machine according to the personal willingness to free to set the required temperature, and can be set through the PID parameter in the table to ensure its accuracy of temperature control, can also be used by itself in the table of system self calculus appropriate temperature control parameters are obtained.
The input force CA(K) TYPE output is 12V.
The current controller has no Relay for SSR and maintains high stability of current.
The hot material is honeycomb stainless steel heating pipe, without pollution and long service life.
Iii. Air supply system:
By circulation of air forced convection air circulation, 1 are motor drives the rotor by the electric heater and hot air from inside air duct to the oven, and will become a source again after using hot air inhaled air duct heating cycle, thereby reducing energy loss and the temperature uniformity in the oven, when the door open and close action cause disturbance, can respond quickly to supply air circulation system operation state temperature.
2 motor for Taiwan imported long shaft high temperature type, power is 1HP50Hz.
The fan is a multi-blade type turbine with high strength, which is equipped with adjustable guide wind board, so that the wind road can be run more smoothly.
Iv. Protection device:
1.Ultra-high temperature protection, no fuse switch, porcelain fuse, motor overload protection.
2.Super - temperature protection, super - load automatic power - off system.
3.Timer: temperature to time, time to power alarm.
4. The warranty period is one year.